60×100 Metal Building Cost in Matagorda County, Texas
Estimated range based on 2026 market data and Matagorda County design requirements. Final pricing requires a dealer quote.
Prefer a kit you install yourself? A 60×100 kit-only package in Matagorda County runs about $73,800 – $110,700 (steel only, no erection or slab). The installed range above includes delivery and erection.
We price 60×100 metal buildings for Bay City, Palacios, Blessing and across Matagorda County.
What the 60×100 estimate includes — and what it doesn't
Most price pages won't tell you this. The slab alone can add a third again on top of the building, so here's the honest breakdown.
Included in the installed range
- The building — frame, roof and wall panels, trim, fasteners
- Engineering for Matagorda County's loads — 149 mph design wind, TDI windstorm (WPI-8)
- Stamped drawings for your permit application
- Delivery to your prepared site
- Professional erection on a level, ready pad
- Anchors for the slab or ground type specified
Not included — budget separately
| Item | Typical cost |
|---|---|
| Concrete slab Texas-typical for 60×100 — about $5.00–$9.00/sq ft. Depends on soils report and local ready-mix. | $30,000 – $54,000 |
| 10×10 roll-up door Each | $1,200 |
| 12×12 roll-up door Each | $1,600 |
| 3'×7' walk-in door Each | $450 |
| 3'×3' window Each | $350 |
| Insulation Double-bubble through R-17 double-layer, quoted per sq ft of covered area (roof + walls), not footprint. | $1.50–$3.00/sq ft |
| Permit fees Set by Matagorda County Environmental Health / Floodplain Administration. Fees differ inside city limits, in the ETJ, and unincorporated — confirm directly. | Varies |
Site prep — clearing, grading, and getting a truck to the pad — is the other variable we can't price for you. A level, accessible site is what keeps an install to a single day; a sloped or tight one is where surprise costs come from.
Price estimator
Estimate your build
Adjust size, county, height and doors for a live range. Same math as the price band above.
What drives the price in Matagorda County
A 60×100 building (6,000 sq ft) is a commercial-scale clear-span building — warehousing, fabrication, ag equipment, fleet, or riding-arena territory. At this size, engineering, wind load, and foundation dominate the price, and turnkey install is usually the practical route. In Matagorda County, the design loads above — not just the size — decide where in the range your price lands.
Matagorda County is open-coast wind country at 149 mph design wind speed — among the highest in Texas. Buildings here are engineered for direct hurricane exposure: heavy-gauge frames, dense fastening, upgraded anchorage, and stamped drawings are not optional. This is the single biggest driver of the price band above, and it's why a building in Bay City costs more than the same size inland.
TDI windstorm certification (WPI-8) applies here
Matagorda County is inside a Texas Department of Insurance (TDI) designated catastrophe area. To insure a structure through the Texas Windstorm Insurance Association (TWIA) — and often to satisfy the local building department — the building must be engineered to TDI standards and pass a WPI-8 windstorm inspection. In practice that means TDI-approved product evaluations, an engineer's design that meets the county wind load, and inspection at framing and completion so the installer can file for the WPI-8 certificate of compliance.
Budget for engineered, stamped plans and the inspection itself. Skipping certification can leave the building uninsurable against wind and hail in this county, so we've built the WPI-8 premium into the coastal price band rather than hiding it.
Foundation & slab in Matagorda County
Steel is only half the job — the concrete under it is the other half. Gulf Coast soils are typically soft coastal clay and sand with a high water table. Slabs here usually need a thicker turned-down edge, more reinforcement, and sometimes select fill — the concrete line item runs higher than the Texas average, and a soils report is money well spent. The slab range shown in the estimator is a Texas-typical figure; your final number depends on a soils report and the local ready-mix price.
Matagorda County is Seismic Design Category A. Like nearly all of Texas, seismic loads do not govern a metal building's design here — wind is the controlling force, not earthquakes — so seismic adds nothing to the price band.
Permits in Matagorda County
For a metal building in Matagorda County, permitting typically runs through the Matagorda County Environmental Health / Floodplain Administration (979-244-2717). Requirements vary by whether you're inside a city limit, in the ETJ, or unincorporated, and most departments want the supplier's engineered, stamped drawings before they'll issue. Confirm current fees and setbacks with the office directly — we verify these links but rules change.
Frequently asked questions
- How much does a 60×100 metal building cost in Matagorda County, TX?
- A 60×100 metal building in Matagorda County typically runs $103,300 – $162,400 installed and delivered. That range reflects Matagorda County's 149 mph design wind speed, TDI windstorm (WPI-8) requirements, and current Texas market pricing. Final pricing requires a dealer quote.
- Why does the price change by county?
- Steel is engineered to local building loads. A county's design wind speed, snow load, seismic category, and — on the coast — TDI windstorm certification all change how much steel and engineering the building needs. That's why Matagorda County has its own price band instead of one statewide number.
- Do I need a permit for a metal building in Matagorda County?
- Usually yes. Permitting typically runs through the Matagorda County Environmental Health / Floodplain Administration, and most departments require the supplier's engineered, stamped drawings. Requirements differ inside city limits versus unincorporated areas — confirm with the office before ordering.
- Does a 60×100 building in Matagorda County need windstorm certification?
- Yes. Matagorda County is in a TDI-designated catastrophe area, so the building must be engineered to TDI standards and pass a WPI-8 inspection to be insurable through TWIA. Budget for stamped plans and the inspection; both are included in the coastal price band shown here.