50×80 Metal Building Cost in El Paso County, Texas
Estimated range based on 2026 market data and El Paso County design requirements. Final pricing requires a dealer quote.
Prefer a kit you install yourself? A 50×80 kit-only package in El Paso County runs about $40,800 – $61,200 (steel only, no erection or slab). The installed range above includes delivery and erection.
We price 50×80 metal buildings for El Paso, Socorro, Horizon City, San Elizario and across El Paso County.
What the 50×80 estimate includes — and what it doesn't
Most price pages won't tell you this. The slab alone can add a third again on top of the building, so here's the honest breakdown.
Included in the installed range
- The building — frame, roof and wall panels, trim, fasteners
- Engineering for El Paso County's loads — 105 mph design wind
- Stamped drawings for your permit application
- Delivery to your prepared site
- Professional erection on a level, ready pad
- Anchors for the slab or ground type specified
Not included — budget separately
| Item | Typical cost |
|---|---|
| Concrete slab Texas-typical for 50×80 — about $5.00–$9.00/sq ft. Depends on soils report and local ready-mix. | $20,000 – $36,000 |
| 10×10 roll-up door Each | $1,200 |
| 12×12 roll-up door Each | $1,600 |
| 3'×7' walk-in door Each | $450 |
| 3'×3' window Each | $350 |
| Insulation Double-bubble through R-17 double-layer, quoted per sq ft of covered area (roof + walls), not footprint. | $1.50–$3.00/sq ft |
| Permit fees Set by El Paso County Public Works — Planning & Development. Fees differ inside city limits, in the ETJ, and unincorporated — confirm directly. | Varies |
Site prep — clearing, grading, and getting a truck to the pad — is the other variable we can't price for you. A level, accessible site is what keeps an install to a single day; a sloped or tight one is where surprise costs come from.
Price estimator
Estimate your build
Adjust size, county, height and doors for a live range. Same math as the price band above.
What drives the price in El Paso County
A 50×80 building (4,000 sq ft) is a commercial-scale clear-span building — warehousing, fabrication, ag equipment, fleet, or riding-arena territory. At this size, engineering, wind load, and foundation dominate the price, and turnkey install is usually the practical route. In El Paso County, the design loads above — not just the size — decide where in the range your price lands.
El Paso County carries an ASCE 7-22 design wind speed of 105 mph (Risk Category II), which is near the Texas inland baseline. A standard engineered metal building meets this with typical bracing and anchor-bolt spacing, so wind adds little or nothing to the base price here — the frame you'd order for most of North and Central Texas.
Foundation & slab in El Paso County
Steel is only half the job — the concrete under it is the other half. West Texas ground is generally firm caliche and rocky soil with very low rainfall, which is good news for foundations — slabs here are often more straightforward and less expensive than in the clay belts to the east. Rock excavation is the main variable to check. The slab range shown in the estimator is a Texas-typical figure; your final number depends on a soils report and the local ready-mix price.
El Paso County falls in Seismic Design Category C — the highest in the Texas seed and unusual for the state. It calls for modest additional lateral bracing and anchorage detailing over a Category A/B building. The effect on price is small but real, and it's included above.
Permits in El Paso County
For a metal building in El Paso County, permitting typically runs through the El Paso County Public Works — Planning & Development (null). Requirements vary by whether you're inside a city limit, in the ETJ, or unincorporated, and most departments want the supplier's engineered, stamped drawings before they'll issue. Confirm current fees and setbacks with the office directly — we verify these links but rules change.
Frequently asked questions
- How much does a 50×80 metal building cost in El Paso County, TX?
- A 50×80 metal building in El Paso County typically runs $57,100 – $89,800 installed and delivered. That range reflects El Paso County's 105 mph design wind speed and current Texas market pricing. Final pricing requires a dealer quote.
- Why does the price change by county?
- Steel is engineered to local building loads. A county's design wind speed, snow load, seismic category, and — on the coast — TDI windstorm certification all change how much steel and engineering the building needs. That's why El Paso County has its own price band instead of one statewide number.
- Do I need a permit for a metal building in El Paso County?
- Usually yes. Permitting typically runs through the El Paso County Public Works — Planning & Development, and most departments require the supplier's engineered, stamped drawings. Requirements differ inside city limits versus unincorporated areas — confirm with the office before ordering.